Electrical - new installation swms 10 checklist

Template Questions

• Business Name: 12 Cassam St Yeppoon Qld 4703
• Business Address: 12 Cassam Dt Yeppoon Qld 4703
• Business Contact: Narelle Jack
• ABN: 47139584053
• Phone No: 0749392000
• SWMS APPROVED BY: Grantley Jack (Employer/PCBU/Director/Owner)
• Date: Date
• Name and Signature of person responsible for ensuring compliance with SWMS:
• Person/s Responsible for Reviewing the SWMS:
• SWMS amendments must be approved by
• Name and Signature:
• ALL PERSONS INVOLVED IN TASK MUST HAVE THIS SWMS COMMUNICATED TO THEM PRIOR TO WORK COMMENCING:- Dail
• Workers to be consulted:
• Job Title:
• The builder or the organisation you are working for.
• Principal Contractor Company Name:
• Project Name:
• Job Address:
• Project Manager Name and Signature:
• Date SWMS provided to Principal Contractor: Date
• This SWMS covers general safety hazards and risks involved with new electrical installations.
• Document #: 10090
• This work activity involves the following "High Risk Construction Work"
• High Risk Construction Work
• Ensure all PPE meets relevant Australian Standards. Inspect and replace PPE as needed.
• Personal Protective Equipment (PPE)
• Potential Hazard
• Liaise with Principal Contractor to establish the following on-site systems and procedures are in pla
• · If working at heights above 2m and “in built’ edge protection is not in place or not sufficient ens
• - Ensure a Confined Space Entry Permit is issued, as required, if work involves a Confined Space. If
• If operating powered mobile plant e.g. excavator, skid steer etc., for this task, ensure there are se
• A ‘Buddy’ system must be utilised at all times when working alone. Ensure: · An emergency response pr
• Person responsible to implement control measures:
• Lack of training or the assessment of capability may lead to personal injury, property damage &/or en
• · Ensure all persons entering site have a General Construction Induction Card (white card)· All worke
• Check constantly for mobile plant and vehicle movement. Ensure:· Follow traffic management plan direc
• Assess conditions at site on arrival. Ensure:· Ensure site-specific induction is undertaken (include
• · Movement of material from the delivery point to the installation area usually represents the greate
• · Park working vehicle to avoid travelling across roads when delivery working equipment· If setting u
• · Ensure equipment is not placed in areas where they may be run over, damaged or exposed to water (un
• · All noisy construction work conducted within regulated hours ( see local council / EPA for details)
• Ensure current Material/Safety Data Sheets (M/SDS) are obtained for all hazardous chemicals/substance
• Ensure underground services have been identified and marked accurately for depth and position: · Cont
• · Ensure all trenches are minimum 650 mm deep· Ground workers (Refer to step 3 for controls - Contact
• Do not:· Assist machine by hand when in operation· Use tools (such as shovels) to help move dirt from
• When working on top of excavations: · Erect any barriers & signage necessary to keep others safe and
• Check if excavations will cause a hazard to others e.g. left open overnight. If potential public haza
• Cutting conduit to length. Ensure:· Use conduit cutters where possible· Sound surface and stable foot
• · Ensure hazard tape is laid above conduits when installed in an open-cut trench· NOTE: The marker ta
• Priming fluid and solvent cements. Ensure:· Use glues recommended by pipe manufacturer · Have applica
• · Ensure a Risk Assessment has been carried out (for any work within 3m of Energised Electrical Insta
• · Ensure point of attachment service brackets and their supports including private poles, supports, s
• Ensure point of attachment can be safely reached by a portable extension ladder:· All trip hazards /
• Ensure point of attachment placed to avoid, where practical, the crossing of driveways or other areas
• All electrical conductors and parts, including neutral & earthing conductors, shall be treated as ene
• Take extra care when working in areas of reduced mobility because of restriction of movement and the
• PPE must be applicable and specific to the site and task. At minimum wear:· Long sleeved cotton shirt
• · Fit “Out of Service Tags” to any incomplete work· Locks & Danger Tags to only be removed by compete
• Hazardous manual tasks - MSD
• · If required, assemble cabinets on ground level · Ensure persons do not work in awkward postures (su
• Barricading and signage is developed. Ensure:· Signs used to provide clear instruction on entry permi
• · Pre-inspect and use ladders as per manufacturers instructions· Avoid using metallic, wire-reinforce
• · Follow directions of use· Consult M/SDS for the product· Ensure adequate ventilation · Dispose of c
• · Use tools only for the purpose specified by the manufacturer· Maintain, pre-inspect and operate the
• Identify all hazards. Consider: · Ground/floor surface condition · Where ground surfaces may change l
• · Ensure equipment is as close to work area as possible· There is adequate space to carry out the act
• All electrically hard wired appliances & fixtures must be installed as per manufactures instruction:·
• When using laser levels, ensure all persons operating laser have been trained and are competent in th
• Testing Equipment: · Good condition and working (particularly, leads, probes, clips) · Clean, no crac
• Contact with electricity
• · All components to be tested after the installation and before being placed in operation · Perform p
• Have you identified any further hazards on the job site?
• What job step does this hazard relate to?
• Risk-Rating (IR) before control measures have been put in place
• Control measures used to reduce risk
• Risk-Rating (RR) after control measures have been put in place.
• · Site to be left in clean and tidy condition ready for handover. Builder / supervisor to be advised
• · Dispose of hazardous chemicals/sealants in an approved waste receptacle.
• · Ensure that no electrical appliances, light fittings, cables etc. have been damaged during installa
• · Clean debris and ensure off cuts are removed from area· Observe good personal hygiene including was
• · If acceptable, remove barricades, contact supervisor and return as agreed· Final visual inspection
• Emergency Response - CALL 000 IMMEDIATELY.
• If work is to be conducted on a construction site (or a site controlled by another Employer / PCBU) f
• Ensure workers have access to:· First aid kit/supplies · First Aid trained personnel familiar with Re
• Note: Retain only the legislation references applicable to your state of operation for this SWMS.
• Relevant Legislation:
• Codes of Practice
• AS/NZS 3000: (Wiring Rules)AS/NZS 3012 Electrical Installations – Construction and demolition sitesAS
• Reference Documents
• Training and Licences Required For Workers Undertaking This Task. Select those relevant
• Licence details
• Photo of relevant licences
• Plant/Tools/Equipment Required For The Job
• Make & Model
• Plant/macinery photo
• Supervisory arrangements for this task:
• Enter relevant information
• Details of Regulatory Permits / Licenses / Engineering Details / Certificates / Work Cover Approvals:
• Item Details
• Overall Risk Rating After Controls
• This SWMS has been developed in consultation and cooperation with employee/workers and relevant Emplo
• Employee/Worker Name and Signature:
• Job Role/Position
• Employer/PCBU/Supervisor:
• To ensure controls are implemented and monitored effectively:• Toolbox /pre-work meetings will be und
• Ensure all controls are reviewed as per the following:• If controls fail to reduce risk adequately• W
• Review Number
• Name & Initials
• Date Date